Have You Identified the Real Reason Behind the Drop in Amplitude?

Definition

Amplitude is the displacement of a vibrating component from its reference position. Suppliers may specify single amplitude or peak-to-peak displacement, and the convention must be confirmed before comparing readings.

Frequency is the number of vibration cycles per unit time. It is determined primarily by the drive speed and the exciter configuration.

Amplitude drop in this context means a measured reduction in displacement compared with the machine’s baseline, after confirming that the measurement method is consistent.

Working Principle

Amplitude is the result of a complete dynamic system. The motor and transmission supply speed to the exciter. The exciter generates periodic force. The screen body, supports and material load determine the resulting motion.

Drive speed. A motor running below its rated speed, a VFD set below the specified frequency, or an electrical supply problem all reduce the speed reaching the exciter. Because force scales with the square of speed, a modest speed reduction produces a disproportionate force reduction.

Transmission. Belts, pulleys, couplings, shafts and keys carry the power from motor to exciter. Slip at any of these points reduces exciter speed even when motor speed is correct. Belt slip is the most common single cause of reduced amplitude on belt-driven screens.

Exciter. Eccentric weights, bearings, gears and lubrication determine the force generated at a given speed. Weight position, locking, condition and assembly all affect output. Internal wear produces resistance, noise and heat.

Structure. Screen body mass, stiffness, joints and support arrangement determine how force becomes motion. Cracks, loose fasteners, damaged springs and foundation problems change the response without changing the force generated.

Load. Material adds effective mass to the system. Excessive feed, uneven distribution, wet material, blockage and accumulation increase the load beyond the design condition and reduce the observed motion.

Benefits

  • Correct diagnosis first time, avoiding replacement of serviceable motors and exciters.

  • Lower repair cost when the fault is identified at the cheapest point in the system.

  • Reduced downtime when the actual cause is found quickly.

  • Structural protection when excessive vibration is avoided rather than created by trial adjustments.

  • Better spare parts planning when failure modes and consumption rates are recorded.

  • Reliable trending when baseline measurements are established and maintained.

Applications

  • Large mining screens in iron ore, copper ore, gold ore and base metal circuits.

  • Aggregate processing screens operating continuously under abrasive duty.

  • Coal preparation where wet screening and variable feed apply.

  • Belt-driven screens where transmission slip is a frequent cause of reduced amplitude.

  • Direct-coupled and vibration motor installations where motor and coupling condition are primary.

  • Dual-motor linear screens where weight configuration and synchronization are critical.

These duties sit between size reduction in CRUSHING and downstream CLASSIFICATION or DEWATERING. Amplitude reduction propagates as mis-sized feed into the next stage.

Material Comparison

Property Drive Speed Fault Transmission Fault Exciter Fault Structure or Load Fault
Frequency Reduced Reduced Normal or unstable Normal
Amplitude Reduced at all points Reduced at all points Reduced, possibly uneven Reduced or uneven
Detection Electrical measurement Speed comparison, belt inspection Bearing temperature, weight position Amplitude mapping, structural inspection
Repair cost Moderate Low Moderate to high Low to moderate
Risk if misdiagnosed Replacing motor unnecessarily Replacing exciter unnecessarily Adjusting weights without approval Compensating with increased force

Application Comparison

Scenario Dominant Symptom Diagnostic Priority
Amplitude and frequency both reduced Speed loss Motor supply, VFD, belt slip
Frequency normal, amplitude reduced Force or response loss Weights, bearings, structure
Amplitude reduced on one side Asymmetry Springs, structure, dual-motor synchronization
Amplitude normal, throughput reduced Process issue Feed distribution, blinding, aperture
Recent maintenance preceded the change Configuration change Verify weights, belts, fasteners against drawing
Sudden change during operation Component failure Transmission, bearing, structural failure

Industry Application Matrix

Industry Typical Drive Common Amplitude Drop Cause Diagnostic Priority
Iron ore Belt-driven large frame Belt slip Belt condition and tension
Copper Belt or direct-coupled Coupling wear, bearing wear Coupling and bearing inspection
Gold Multi-motor linear Weight configuration mismatch Weight position, rotation direction
Coal Belt-driven sealed units Contamination, belt slip Sealing, belt condition
Aggregates Belt-driven Belt tension, spring degradation Belt and spring inspection
Sand and gravel Vibration motors Motor supply, bearing wear Electrical and bearing check
Industrial minerals Belt or direct Bearing damage, misalignment Bearing and alignment
Base metals Heavy-duty belt-driven Belt failure, structural movement Belt and structural inspection
Phosphate Sealed belt-driven Corrosion-related electrical fault Electrical and sealing
Tailings Dewatering screens Belt slip, spring condition Belt and support inspection

Selection Guide

1. Confirm the measurement. Single or peak-to-peak. Same instrument, same points, same orientation, same operating condition as baseline.

2. Record frequency and operating speed. Screen vibration frequency, motor speed and exciter speed where accessible. Compare with approved values.

3. Review the process condition. Feed rate, distribution, moisture, particle size, deck loading, recent production changes.

4. Check the electrical and motor system. Qualified personnel inspect supply, motor condition, current, VFD settings.

5. Inspect the transmission. Belts, pulleys, couplings, shafts, keys and mounting for wear, slip, looseness and alignment.

6. Inspect the exciter. Eccentric settings against drawing, bearings, gears, shafts, lubrication, housing condition.

7. Inspect the screen and supports. Cracks, loose fasteners, damaged springs, foundation problems, abnormal contact.

8. Correct the confirmed cause and remeasure. Document the repair and compare post-maintenance readings with the original specification.

Procurement Guide

Required information: screen make and model, measured amplitude and frequency, motor and exciter identification, operating speed, recent maintenance history, vibration-analysis results, feed conditions, photographs of the drive and deck.

Drawings needed: exciter assembly drawing with eccentric weight positions, drive arrangement drawing, spring and support specification.

OEM part numbers: obtain original references for weights, belts, couplings, bearings, springs and electrical components.

Material selection: confirm bearing specification, weight material, belt grade, spring type and electrical protection class.

MOQ, lead time, packaging and shipping: confirm lead time against shutdown, packaging for heavy components.

Inspection standards: dimensional check, weight position verification, bearing verification, spring dimensional check, electrical testing.

Supplier evaluation checklist — ask directly:

  • Can you supply components matched to our screen model and exciter configuration?

  • Can you provide weight position drawings and spring specifications?

  • Can you support OEM replacement for exciters, weights and drive components?

  • Do you have export experience in our region?

  • Can you provide application references for similar screens?

The WHICH MANUFACTURER OFFERS HIGH-QUALITY POLYURETHANE TUFFLEX WIRE SCREENS FOR MINING? guide expands on supplier evaluation.

Failure Analysis

Problem Possible Cause Recommended Solution
Amplitude and frequency both reduced Belt slip, motor speed, VFD setting Inspect belt, verify motor speed, check VFD
Frequency normal, amplitude reduced at all points Weight position, bearing wear, exciter internal damage Verify weights, inspect bearings, oil condition
Amplitude reduced on one side Spring damage, structural deflection, motor sync issue Inspect springs, structure, motor rotation
Amplitude reduced under load only Excessive feed, deep bed, blockage Review feed rate and distribution
Amplitude measurement inconsistent Different instrument, point or convention Use calibrated instrument at defined points
Sudden amplitude loss during operation Belt break, coupling failure, bearing seizure Isolate and inspect immediately
Amplitude reduced after maintenance Configuration changed, weights wrong, belt loose Verify against drawing, re-tension, re-torque
Spring broken or deformed Fatigue, incorrect installation, overloading Replace with specified spring, verify installation
Loose structural fasteners Insufficient torque, vibration loosening Re-torque to specification, inspect for fatigue
Cracks at side plate or beam Excessive vibration, fatigue, structural defect Stop operation, inspect, repair under engineering approval

Maintenance Guide

Daily: record amplitude and frequency at defined points; note changes in noise, current or material movement.

Weekly: inspect belt tension and condition; verify spring condition; check mounting bolt tightness.

Monthly: compare amplitude and frequency trends against baseline; inspect structure and supports; verify eccentric weight security.

Baseline measurement: record amplitude and frequency at fixed points during commissioning and after any maintenance involving drive, exciter or structure.

Spare parts inventory: hold belts, springs, fasteners and bearings sized to consumption rate.

Downtime reduction: pre-stage common failure components before shutdown.

Documentation: record each fault, diagnosis and correction with before and after readings.

Preventive maintenance: treat belt condition, spring condition and fastener torque as primary items.

Case Study

Customer Type: Mid-size aggregate producer with a belt-driven vibrating screen on a primary sizing duty.

Material: Crushed limestone with variable moisture.

Operating Conditions: Continuous production with monthly inspections. Amplitude and frequency measured at four corners at each inspection.

Problem: Monthly inspection showed amplitude reduced from 9 mm to 6.5 mm at all four corners, with frequency unchanged. Material throughput had fallen noticeably.

Solution: A structured diagnostic was applied. Step 1 confirmed the measurement: same instrument, same points, same condition — the reduction was real. Step 2 showed frequency unchanged, which made a speed loss less likely. Step 3, transmission inspection, found the belt in good condition with correct tension. Step 4, exciter inspection, showed weights at correct positions with locking devices secure. Step 5, amplitude mapping at all four corners, showed the reduction was uniform. Step 6, spring inspection, found one spring partially collapsed, which was affecting the overall response rather than one corner.

Result: Spring replaced with specified part. Amplitude returned to approximately 8.8 mm at all four corners on the next measurement. The uniform reduction across all corners was the clue that pointed to a system-level cause rather than a localised drive or structure fault. The plant added spring dimensional check to the quarterly inspection.

Figures reflect a realistic single-site investigation and are not a guaranteed performance claim.

FAQ

Q1: What is the normal amplitude for a vibrating screen?
There is no single amplitude value suitable for every vibrating screen. The required displacement depends on screen design, application, deck arrangement, material properties, operating frequency and manufacturer’s specification. Some documents state single amplitude, others report peak-to-peak displacement. Use the machine’s approved operating range rather than a generic industry figure.

Q2: Why has amplitude decreased but vibration frequency stayed the same?
If frequency is stable but amplitude has decreased, check eccentric configuration, exciter condition, structural response, support system and effective screen load. Also confirm the measurement point and instrument setup have not changed. Stable frequency makes a simple speed-loss explanation less likely, but it does not identify the cause by itself.

Q3: Can worn screen panels cause a drop in amplitude?
Worn panels usually affect screening efficiency, aperture accuracy, material passage and deck condition rather than directly reducing the force generated by the exciter. However, panel damage, loose components, material build-up or abnormal deck load can influence mass distribution and observed machine response. Separate the vibration measurement from the screening result.

Q4: What does uneven amplitude across the screen indicate?
Uneven amplitude may indicate an asymmetrical drive or exciter condition, incorrect eccentric settings, structural damage, support-spring differences, loose fasteners, uneven loading or inconsistent measurement. Compare readings at the specified points and check whether the pattern is repeatable. Do not attempt to balance by trial-and-error weight adjustments.

Q5: Should I increase the motor speed to restore amplitude?
Not unless the equipment manufacturer’s operating procedure specifically permits the change and the cause has been established. Increasing speed raises dynamic forces and stress on bearings, shafts, structural members, supports and foundations. It may also move the machine outside its designed operating range.

Q6: How much does it cost to correct an amplitude problem compared with replacing the exciter?
The cost depends entirely on the cause. A belt replacement and re-tension is a low-cost intervention. A spring replacement is moderate. An exciter overhaul or replacement is a significant cost with procurement lead time and installation labour. This is why diagnosing the cause before ordering parts matters more than the cost of any individual component.

Q7: Why does amplitude drop only under load?
This pattern indicates a load-related issue rather than a drive fault. Possible causes include excessive feed, uneven distribution, wet or sticky material, blocked apertures or a screen deck overloaded for its design capacity. Measure amplitude under both empty and loaded conditions to confirm.

Q8: Can a loose fastener cause amplitude to drop?
A loose fastener or structural connection can change the machine’s dynamic response by allowing movement that was not designed. This can produce uneven amplitude, abnormal noise or accelerated wear at the connection point. Inspect fasteners at scheduled intervals and re-torque to specification.

Q9: How often should amplitude be measured?
At commissioning, after any maintenance involving the drive, exciter or structure, and at regular intervals during operation. The measurement interval should reflect the criticality of the screen and the stability of its operating conditions. Monthly is common for critical screens; quarterly may be sufficient for others.

Q10: Is a drop in amplitude always a problem?
Not always. Amplitude can change with load, material properties and operating conditions. The question is whether amplitude has changed compared with the baseline under comparable conditions, and whether screening performance has been affected. A drop that is explained by a known process change is not a fault. An unexplained drop is.

Conclusion

A drop in vibrating-screen amplitude is a system-level symptom, not a diagnosis. The motor may be responsible, but the transmission, exciter, eccentric weights, screen structure, support system, measurement method and material load all deserve consideration.

Confirm amplitude and frequency with repeatable measurements, trace the drive from motor to exciter, and inspect the structure and process before replacing components or changing settings. Use the OEM’s limits and safe isolation procedures throughout.

If you are investigating reduced screen performance, HTL can review your equipment details and operating requirements.

Related Articles

Related Products

Related Technical Guides

Related Buyer Guides

Related Comparison Articles

Contact

Annie Lu
Email: annie.lu@huataogroup.com
Mobile / WhatsApp / WeChat: +86 18032422676
Website: https://www.tufflexscreen.com

Tags:
avatar admin
personal profile

Products

Pinch Valve Sleeve Liner

Liquid Phase Wear-Resistant Rubber Pinch Valve Sleeve Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
slurry pump liner

Liquid Phase Wear-Resistant Rubber Slurry Pump Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
Magnetic separator lining (1)

Liquid Phase Wear Resistant Rubber Magnetic Separator Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
red rubber (11)

Custom Liquid Phase Rubber Lining Solutions

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.

Liquid Phase Wear Resistant Rubber Cross Beam Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
red rubber (13)

Premium Natural Rubber Sheet for Mining Wear Protection

HUATAO Liquid-Phase Compounded Wear-Resistant Natural Rubber Sheet is designed for demanding mining, mineral processing and slurry handling applications. Manufactured using a specialized liquid-phase compounding process and high-quality natural rubber, it offers excellent resistance to wet abrasion, cutting and tearing, combined with high elasticity and resilience.
product

Contact us

    Products
    Contacts
    WhatsApp
    Email