Definition
Exciting force is the periodic force generated by the vibration mechanism — eccentric weights rotating at operating speed. In simplified form, F = m × r × ω², where m is unbalanced mass, r is eccentric radius and ω is angular speed.
Screen amplitude is the displacement of the screen during its motion. It is related to exciting force but not equivalent, because the screen’s mass, stiffness, support arrangement, operating frequency and damping determine how the applied force translates into movement.
Insufficient exciting force in this context means the screen is not delivering the motion required for effective material transport and separation, whether because the force generated is low or because the machine does not respond to it as designed.
Working Principle
Exciting force is generated at three points in the system, and a fault at any point produces a similar symptom.
Generation. Eccentric weights rotate at operating speed and produce centrifugal force. The force depends on unbalanced mass, eccentric radius and the square of speed. A weight incorrectly positioned, missing or installed asymmetrically changes the force. A motor running below rated speed changes the force disproportionately.
Transmission. Power reaches the exciter through belts, pulleys, couplings or shafts. Belt slip, incorrect tension, worn pulleys, coupling damage and shaft misalignment reduce the speed reaching the exciter. On a belt-driven screen the motor can run at correct speed while the driven shaft turns more slowly, producing less force.
Response. The screen body, springs and support structure respond to the force. Loose structural bolts, cracked welds, damaged beams and incorrect springs change how the machine moves. The force may be correct while the motion is not.
Load. The material being processed adds effective mass to the system. Excessive feed, uneven distribution, wet or sticky material, blocked apertures and accumulation increase the load beyond the design condition. The screen may fail to convey material without the exciter having stopped generating force.
The correct diagnostic question is not “Is the motor powerful enough?” but “Is the complete machine generating and transmitting the designed motion under the current operating conditions?”
Benefits
-
Correct diagnosis first time, avoiding replacement of serviceable motors and exciters.
-
Lower repair cost when the fault is identified at the cheapest point in the system.
-
Reduced downtime when the actual cause is found quickly.
-
Structural protection when excessive vibration is avoided rather than created by trial adjustments.
-
Better spare parts planning when failure modes are recorded and analysed.
-
Longer component life when root causes are corrected rather than symptoms masked.
Applications
-
Large mining screens in iron ore, copper ore, gold ore and base metal circuits.
-
Aggregate processing screens operating continuously under abrasive duty.
-
Coal preparation where wet screening and variable feed apply.
-
Belt-driven screens where transmission slip is a frequent cause of reduced force.
-
Direct-coupled and vibration motor installations where motor and coupling condition are primary.
-
Dual-motor linear screens where weight configuration and synchronization are critical.
These duties sit between size reduction in CRUSHING and downstream CLASSIFICATION or DEWATERING. Reduced force propagates as mis-sized feed into the next stage.
Material Comparison
| Property | Motor Fault | Transmission Fault | Exciter Fault | Structure or Load Fault |
|---|---|---|---|---|
| Symptom | Low speed, high current, overheating | Correct motor speed, low exciter speed | Abnormal noise, heat, unstable motion | Uneven motion, poor conveying |
| Detection method | Electrical measurement, nameplate comparison | Speed comparison, belt inspection | Bearing temperature, noise, oil condition | Amplitude measurement, structural inspection |
| Repair cost | Moderate to high | Low | Moderate to high | Low to moderate |
| Risk if misdiagnosed | Replacing motor unnecessarily | Replacing exciter unnecessarily | Replacing exciter without fixing root cause | Adjusting weights to compensate |
Application Comparison
| Scenario | Dominant Symptom | Diagnostic Priority |
|---|---|---|
| Motor runs but screen motion is weak | Low amplitude at all points | Transmission slip, exciter condition |
| Screen motion weak on one side | Uneven amplitude | Support springs, structural condition |
| Screen motion normal but no conveying | Correct amplitude, poor transport | Feed distribution, aperture blockage, deck condition |
| Motor current high, speed low | Overload or supply problem | Electrical supply, mechanical resistance |
| Abnormal noise from exciter | Bearing or gear damage | Exciter inspection under OEM procedure |
| Recent maintenance preceded the fault | Configuration change | Verify weights, belts, fasteners against drawing |
Industry Application Matrix
| Industry | Typical Failure Mode | Diagnostic Priority |
|---|---|---|
| Iron ore | Belt slip on large belt-driven screens | Belt tension and pulley condition |
| Copper | Exciter bearing wear | Bearing temperature, lubrication |
| Gold | Weight configuration mismatch on dual motors | Weight position, rotation direction |
| Coal | Wet material overloading | Feed rate, moisture, aperture blockage |
| Aggregates | Loose structural bolts | Fastener torque, structural inspection |
| Sand and gravel | Motor supply issues | Electrical measurement |
| Industrial minerals | Spring degradation | Spring condition, installation |
| Base metals | Coupling damage | Coupling inspection, alignment |
| Phosphate | Corrosion-related electrical fault | Electrical and sealing |
| Tailings | Material accumulation on deck | Feed distribution, deck condition |
Selection Guide
1. Record the symptom. When it began, whether it affects the whole screen or one area, whether it is continuous or intermittent, and whether it followed a repair, adjustment or feed change.
2. Confirm the operating specification. Screen and exciter models, motor nameplate data, approved speed, amplitude, eccentric setting and applicable maintenance instructions.
3. Check the electrical and motor side. Qualified personnel verify supply conditions, current, motor condition, drive settings and actual motor speed against nameplate.
4. Check power transmission. Inspect belts, pulleys, couplings, shafts and connections for slip, wear, misalignment or looseness after safe isolation.
5. Inspect the exciter. Verify the approved eccentric configuration and look for bearing, gear, lubrication or assembly problems.
6. Measure screen motion. Compare amplitude and frequency at consistent measurement locations under comparable operating conditions.
7. Inspect structure, supports and process loading. Loose fasteners, cracks, support problems, uneven feed, excessive loading and material accumulation.
8. Correct the verified cause and retest. Change only approved settings, document the repair, and confirm that motion and screening performance return to the specified range.
Procurement Guide
Required information: screen make and model, exciter type and identification, motor nameplate, operating speed, measured amplitude and frequency, feed material and rate, description of when the problem occurs, recent repair and adjustment history, vibration or temperature records.
Drawings needed: exciter assembly drawing with eccentric weight positions, drive arrangement drawing, motor mounting detail.
OEM part numbers: obtain original references for weights, belts, couplings, bearings and electrical components.
Material selection: confirm bearing specification, weight material, belt grade and electrical protection class.
MOQ, lead time, packaging and shipping: confirm lead time against shutdown, packaging for heavy components.
Inspection standards: dimensional check, weight position verification, bearing verification, electrical testing.
Supplier evaluation checklist — ask directly:
-
Can you supply components matched to our screen model and exciter configuration?
-
Can you provide weight position drawings and specifications?
-
Can you support OEM replacement for exciters, weights and drive components?
-
Do you have export experience in our region?
-
Can you provide application references for similar screens?
The WHICH MANUFACTURER OFFERS HIGH-QUALITY POLYURETHANE TUFFLEX WIRE SCREENS FOR MINING? guide expands on supplier evaluation.
Failure Analysis
| Problem | Possible Cause | Recommended Solution |
|---|---|---|
| Low amplitude at all points | Belt slip; incorrect weight setting; motor speed low | Check belt tension; verify weight position; measure motor speed |
| Low amplitude on one side | Broken spring; structural deflection; uneven load | Inspect springs; measure amplitude at both sides |
| Motor current high, speed low | Supply problem; mechanical resistance; overload | Electrical measurement; check for binding |
| Abnormal noise from exciter | Bearing wear; gear damage; lubrication failure | Exciter inspection under OEM procedure |
| Screen conveys poorly at normal amplitude | Feed distribution; aperture blockage; deck condition | Review feed; inspect media; check deck |
| Fault followed maintenance | Configuration changed during repair | Verify against drawing; restore approved settings |
| Vibration increased after weight adjustment | Weights set beyond approved range | Restore to manufacturer specification |
| Dual motors out of sync | Rotation or weight mismatch | Verify rotation direction and weight positions |
| Loose structural bolts | Insufficient torque; vibration loosening | Re-torque to specification; inspect for fatigue |
| Cracks at beam or side plate | Excessive vibration; fatigue; structural defect | Stop operation; inspect; repair under engineering approval |
Maintenance Guide
Daily: record any change in vibration, noise or current; check for belt slip on belt-driven units.
Weekly: inspect belt tension and condition; verify weight locking devices; check mounting bolt tightness.
Monthly: measure amplitude and frequency at fixed points; check bearing temperature; inspect springs and supports.
Baseline measurement: record amplitude and frequency at fixed points during commissioning and at intervals.
Spare parts inventory: hold belts, weights, fasteners and bearings sized to consumption rate.
Downtime reduction: pre-stage common failure components before shutdown.
Documentation: record each fault, diagnosis and correction. Pattern recognition across failures identifies recurring causes.
Preventive maintenance: treat belt condition, weight security and fastener torque as primary items.
Case Study
Customer Type: Mid-size copper concentrator with a belt-driven vibrating screen on a sizing duty.
Ore Type: Copper ore with hard angular particles.
Operating Conditions: Screen operating continuously. Operator reported reduced material throughput and suspected motor failure. Motor had been replaced six months previously.
Problem: Plant planned to replace the motor again. Downtime estimate was one shift.
Solution: A structured diagnostic was applied. Step 1 confirmed the symptom: reduced throughput, not complete failure. Step 2 confirmed the operating specification. Step 3, electrical check, showed motor speed and current within nameplate limits. Step 4, transmission inspection, found the belt tension below specification with visible glazing on the pulley. Step 5, exciter inspection, found eccentric weights at correct positions but one locking bolt slightly loose. Step 6, amplitude measurement, showed reduced amplitude consistent with the belt slip.
Result: Belt replaced and re-tensioned, weight locking bolt re-torqued. Amplitude returned to the specified range and throughput recovered within two hours. Motor replacement was avoided. The plant added belt tension and weight locking verification to the monthly inspection checklist.
Figures reflect a realistic single-site investigation and are not a guaranteed performance claim.
FAQ
Q1: What is the difference between exciting force and screen amplitude?
Exciting force is the periodic force generated by the vibration mechanism, while amplitude describes the displacement of the screen during its motion. They are related but not interchangeable. The screen’s mass, stiffness, support arrangement, operating frequency and damping influence how the applied force translates into movement. A force-related diagnosis should include both drive-system checks and actual motion measurements.
Q2: Can a vibrating screen have normal motor speed but insufficient vibration?
Yes. The transmission may slip, the exciter may be incorrectly configured or damaged, or the screen structure and supports may not respond as designed. Motor speed alone does not prove the exciter shaft is turning at the correct speed or that the screen is achieving the specified amplitude.
Q3: Does increasing the eccentric weight always improve screening capacity?
No. Increasing unbalance can increase dynamic force, but it also increases loads on bearings, shafts, screen beams, side plates, springs and foundations. The result may be accelerated fatigue, cracking, fastener loosening or premature component failure. Eccentric settings must remain within the manufacturer’s approved range.
Q4: How can I tell whether the problem is the exciter or the screen structure?
Compare measured amplitude and frequency at multiple specified points, inspect the drive and exciter, and examine the support and structural system for damage or looseness. A drive fault may affect overall frequency or force generation, while structural problems may produce uneven motion or localised abnormal response. Use vibration measurements and the manufacturer’s troubleshooting procedure to confirm.
Q5: What information should I provide when asking for a troubleshooting assessment?
Screen make and model, exciter type and identification, motor nameplate, operating speed, measured amplitude and frequency, feed material and rate, a clear description of when the problem occurs, photos or drawings of the drive and deck, recent repair and adjustment history, and any vibration or temperature records.
Q6: How much does a replacement motor cost compared with a belt?
The difference is substantial. A belt is a low-cost consumable, typically available locally. A motor is a major component with procurement lead time and installation labour. This cost difference is the practical reason for diagnosing from the cheapest and most likely cause outward.
Q7: Can I compensate for a mechanical fault by increasing speed?
Not safely. Speed is squared in the force equation, so a small increase produces a large force increase. This overloads bearings, beams and foundations beyond their design. Mechanical faults should be corrected, not compensated for by overdriving the machine.
Q8: Why does the screen vibrate normally when empty but poorly under load?
This pattern indicates a load-related issue rather than a drive fault. Possible causes include excessive feed, uneven distribution, wet or sticky material, blocked apertures or a screen deck that is overloaded for its design capacity. Measure amplitude under both conditions to confirm.
Q9: How often should eccentric weights be checked?
At every exciter inspection and after any maintenance that involves the exciter or drive. Verify weight position against the assembly drawing and confirm locking devices are secure. Record the setting so future maintenance can confirm no drift.
Q10: Should I replace the screen media if the screen is not conveying?
Only after diagnosing the cause. If the problem is drive-related, media replacement will not fix it. If the problem is aperture blockage or media condition, replacement may help. Measure amplitude, inspect the deck and review feed conditions before replacing media.
Conclusion
Insufficient exciting force is not automatically a motor fault. The motor and electrical supply are only the starting point in a system that also includes the transmission, exciter, eccentric weights, screen structure, supports and process load. Confirm actual speed and screen motion, inspect the drive and exciter, and rule out structural and operating-condition problems before replacing components or changing settings.
Never increase motor power or eccentric weight without checking the manufacturer’s limits. If you are investigating reduced screen performance, HTL can review your equipment details and operating requirements.
Related Articles
Related Products
Related Technical Guides
-
IMPROVE FINE SCREENING EFFICIENCY WITH POLYURETHANE SCREEN PANELS
-
HYDROCYCLONE WEAR: ROOT CAUSES, HIGH-WEAR ZONES & MATERIAL SOLUTIONS
-
FLOTATION CELL ROTOR AND STATOR WEAR PARTS: HOW THEY CONTROL RECOVERY, FLOW AND MAINTENANCE COST
-
ROTOR & STATOR IN MECHANICAL FLOTATION CELLS: THE HEART OF EFFICIENT MINERAL FLOTATION
Related Buyer Guides
-
WHICH MANUFACTURER OFFERS HIGH-QUALITY POLYURETHANE TUFFLEX WIRE SCREENS FOR MINING?
-
HOW DO I CHOOSE THE RIGHT RUBBER BELT FOR A VACUUM BELT FILTER?
Related Comparison Articles
-
POLYURETHANE SCREEN VS RUBBER SCREEN VS WIRE MESH: A COMPLETE COMPARISON GUIDE
-
SELF-CLEANING SCREEN VS TRADITIONAL WOVEN WIRE MESH: WHICH ONE SHOULD YOU CHOOSE?
Contact
Annie Lu
Email: annie.lu@huataogroup.com
Mobile / WhatsApp / WeChat: +86 18032422676
Website: https://www.tufflexscreen.com
admin