How Close Should a Self-Cleaning Overband Magnet Be to the Conveyor Belt for Maximum Tramp Iron Capture?

Quick Answer

For most mining conveyors, mount a self-cleaning overband magnet 200–300 mm above the belt — roughly 0.2–0.3 × belt width — then correct upward for burden depth: set the working gap at the maximum material layer thickness plus 50–100 mm of safety clearance, measured from the magnet’s working face to the deepest position a steel piece can occupy. Lower improves capture but risks collision; higher quietly leaks fine tramp iron to your crusher.

Key Takeaways

  • Suspension height is the single most tunable capture variable: magnetic pull decays sharply with distance, so millimetres matter.
  • Start at 0.2–0.3 × belt width (200–300 mm for a 1,000 mm belt), then add burden-depth correction.
  • Measure from the magnet working face to the target object’s deepest position — not to the bare belt.
  • Capture is a time budget: belt speed above 2.5–3.0 m/s makes an electromagnetic circuit mandatory.
  • The magnet face should be 200–400 mm wider than the belt to catch edge-positioned steel.
  • Dust and ore build-up on the magnet face silently widen the gap — clean and test on a fixed schedule.fig1 overband magnet suspension height

Case Study

Customer Type: Iron ore surface mine, concentrator crushing line

Ore Type: Iron ore (magnetite-bearing, dense, 150–400 mm lumps)

Operating Conditions: 1,400 mm belt, 2.2 m/s, 900 t/h, burden depth 180–260 mm depending on feed

Problem: A permanent overband was mounted 450 mm above the belt “for safety” after one lump-strike incident. Fine steel began reaching the primary crusher; over one quarter, three jaw plate change-outs were pulled forward and one belt puncture occurred. Capture testing with marked witness pieces showed recovery of small steel below 40%.

Solution: The installation was re-engineered rather than simply re-hung: an electromagnetic unit sized to penetrate the full 260 mm burden was installed with a documented working gap of 330 mm (burden + 70 mm clearance, measured to the deepest target position), a face 300 mm wider than the belt, a metal-detector interlock to suppress magnetite pickup, and a re-angled discharge chute. The monthly gap-measurement log was added to the existing conveyor inspection route alongside the Mining Secondary Belt Cleaner checks.

Result: Witness-piece capture of small steel rose from under 40% to above 95%; jaw plate life returned to plan (no premature change-outs for two consecutive quarters); belt damage events dropped to zero; and the gap log caught one 40 mm build-up drift within a single month — corrected in a 20-minute stop. The mining team’s own number: protection restored for the cost of one avoided jaw plate set.fig3 measuring working gap

Related Articles

Related Products

  • Iron Magnet
  • Self-Cleaning Electromagnetic Separator
  • Magnetic Drum
  • Heavy-Duty Conveyor Impact Bed
  • Conveyor Belt Tracker

Related Technical Guides

  • Magnetic Separation Process Equipment
  • Conveyor Process Equipment
  • Crushing Process Equipment
  • Improve Fine Screening Efficiency with Polyurethane Screen Panels
  • Hydrocyclone Wear: Root Causes, High-Wear Zones & Material Solutions

Related Buyer Guides

  • Which Manufacturer Offers High-Quality Polyurethane Tufflex Wire Screens for Mining?
  • How Do I Choose the Right Rubber Belt for a Vacuum Belt Filter?

Related Comparison Articles

  • Polyurethane Screen vs Rubber Screen vs Wire Mesh: A Complete Comparison Guide
  • Self-Cleaning Screen vs Traditional Woven Wire Mesh: Which One Should You Choose?

Contact Us

Contact: Annie Lu

Email: annie.lu@huataogroup.com

Phone / WhatsApp: +86 180 3242 2676

Website: http://www.tufflexscreen.com

We warmly welcome customers from around the world to contact us and establish mutually beneficial partnerships.

avatar admin
personal profile

Products

Pinch Valve Sleeve Liner

Liquid Phase Wear-Resistant Rubber Pinch Valve Sleeve Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
slurry pump liner

Liquid Phase Wear-Resistant Rubber Slurry Pump Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
Magnetic separator lining (1)

Liquid Phase Wear Resistant Rubber Magnetic Separator Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
red rubber (11)

Custom Liquid Phase Rubber Lining Solutions

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.

Liquid Phase Wear Resistant Rubber Cross Beam Liner

Our abrasion-resistant rubber plates are suitable for mineral processing plants, material transfer systems, and heavy-duty machinery. Custom thicknesses and dimensions can be supplied according to your equipment requirements.
red rubber (13)

Premium Natural Rubber Sheet for Mining Wear Protection

HUATAO Liquid-Phase Compounded Wear-Resistant Natural Rubber Sheet is designed for demanding mining, mineral processing and slurry handling applications. Manufactured using a specialized liquid-phase compounding process and high-quality natural rubber, it offers excellent resistance to wet abrasion, cutting and tearing, combined with high elasticity and resilience.
product

Contact us

    Products
    Contacts
    WhatsApp
    Email